U2C S+ Maxi перестал запускаться.
перешивается по COM и USB без проблем.
после прошивки:
Скрытый текст
Boot form SPI v1.08
SPI SCS flow
Cal▒CLK
F64K
v1.61
CK=00
*
#2
IPR=59
G=1A
IPR/4=16
G>/4
IPR/2+6=32
G</2+6
G1=10
Q-0x1C=06
G1>Q-1C
Q+5= 1F
G1<Q+5
~G=1A
G1=10
#3
#4
DRAM-2GTRIM-O
copy fw to RAM
GO!!
1ST BOOT
Zero BSS
IntCtrl
LD eCos v1.05
[FIRST_BOOT] rom start addr. is 0x98000000
[FIRST_BOOT] Get the fp of operations
[FIRST_BOOT] Init. for the interface of flash
[FIRST_BOOT] getModuleTable !
[FIRST_BOOT] this module is first one module
[FIRST_BOOT] Load tb_idx = 0, mod_idx = 0
[FIRST_BOOT] lma = 0x00010400, lma_size = 0x00014198, vma = 0x81600000, vma_size = 0x00014198, attr = 0x80000001, scramble_key = 0x00000000, crc32 = 0x9C812AEB
[FIRST_BOOT] comp_method = 1
[FIRST_BOOT] Use 0xA2040000 ~ be hw temporary buffer!
[FIRST_BOOT] uncompressing on ram...
[FIRST_BOOT] uncompressing... src_ram: 0xA2088000, data: 0xB8005053
[FIRST_BOOT] uncompress err num: 188416
[FIRST_BOOT] Module 0: vma = 0x81600000
Go eCos
Boot from SPI
eCos 2.073T
MMU
FPU
IntC
Cache
Timer
Cache region
Mon
Zero BSS
Var Init
Plf Init
Get IOP Data
Ctor Init
0x81624B9C
0x8160D0AC
0x8160B820
0x8160C660
0x8160BE2C
0x81609B9C
0x81626F70
heap:=0x816f2668
__heap1:=0x816f2668
heap:=0x816f2768
__heap1:=0x816f2668
0x81626658
0x8161A288
0x816219AC
0x816219AC
0x816219AC
0x816219AC
0x8161A8C4
0x81628450
0x81628410
0x81628610
0x816282AC
0x8162C3D0
cyg_start
m_info->lma:=0x24800,m_info:=0x81630230,PLF_GetRomStartAd dr:=0x98000000 ~~~~~~~~~
uncompress!
m_info->lma:=0x24800,m_info:=0x81630230 ,m_info->vma:=0x816b7468,info->vma_size=0x3b200,res:=0x0~~~~~~~~~
m_info->lma:=0x0,m_info:=0x81630230,PLF_GetRomStartAddr:= 0x98000000 ~~~~~~~~~
m_info->lma:=0x0,m_info:=0x81630230,PLF_GetRomStartAddr:= 0x98000000 ~~~~~~~~~
m_info->lma:=0x0,m_info:=0x81630230,PLF_GetRomStartAddr:= 0x98000000 ~~~~~~~~~
enter to card pin init
GPIO function 3[0], not assign pin number
bootloader [NVM] Boot from SPI
[SPI] init_spi_flash
[SPI] Ver 0101a916
[SPI] op code=9F, system_flash_id 0x0017301c
[SPI] op code=90, system_flash_id 0x0000161c
[SPI] flash_info 0x17301C0412
[SPI] flash name EON_Q64
[SPI] 1 bit mode
i32LoaderHeaderOffset:=0x3cb5c
main version:=4
sub version:=13
app version:=1
i32LoaderHeaderOffset:=0x3cb5c
FIRSTBOOT_SIZE:=0x10000
u32Offset:=0x80010
i32RomCodeHeaderOffset:=0x6e4000
gs_stLoaderHeader.uiPrivateStartAddr:=0x7f000
▒UFIRSTBOOT_SIZE:=0x10000
u32Offset:=0x80010
i32RomCodeHeaderOffset:=0x6e4000
line1414: stMainHead.sw_version:=0x1234
sw_model:=0x2000
OUI[0]:=0x5
OUI[1]:=0x11
OUI[2]:=0x0
file_len:=0x664000
crc32:=0xe448f94f
flag[0]:=S
flag[1]:=P
flag[2]:=H
flag[3]:=E
flag[4]:=1
flag[5]:=5
g_i32BootloaderSize:=0x80000
bootloader_size:=0x80
uiDefaultDBStartAddr:=700000
line1430: stMainHead.uiDefaultDBSizeK:=0x60
CRC OK!
FIRSTBOOT_SIZE:=0x10000
u32Offset:=0x80010
FIRSTBOOT_SIZE:=0x10000
u32Offset:=0x80010
i32RomCodeHeaderOffset:=0x6e4000
jame add-----main_program-----268-----Wire NETWROK MAC_Addr-----001105D8CF86
eCos 2.073T
MMU
FPU
IntC
Cache
Timer
Cache region
Mon
Zero BSS
Var Init
Plf Init
Get IOP Data
Ctor Init
cyg_start
wen ota init SUCCESS
wen read error!
и цикличный ребут.
что такое wen read error? куда копать?
благодарю.