[Āris]

kolos, 1. Обновление программного обеспечения



a)Подготовить нуль модемный кабель RS232C (pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).

b)Подключить компьютер к ресиверу при помощи RS- 232C кабеля. Для безопастности, выключите компьютер и ресивер перед подключением.

c)Включите ресивер и при помощи кнопки "POWER" переведите его в ждущий режим.

d)Запустите утилиту обновления,войдите в меню <Download software>, <Browse> и выберите .bin файл, затем нажмите <Start> для начала обновления.

e)Во время обновления ПО, индикатор будет показывать "dxxx"(Передача данных в память),"-ES-"(Очистка флеш),затем "Pxxx"(запись данных на флеш),и в завершении "-End"

f)Выключите ресивер,отсоедините RS- 232C кабель и включите его.
1.How to update s/w by PC?
======================
1) Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
2) Connect your PC and receiver with twisted RS-232C cable.
3) Turn on the receiver and press "POWER" key to make it standby, the LED dot will blink.
4) Run the update tool on your PC,Slect the <Download Main S/W>,press <Open> and select the bin file,then click <Start>,upgrade will begin.
5) After finishing, the LED will display "-End"

=========================================
2.How to Enable Patch or Disable Patch?
=========================================
Main Menu-->STB Setting-->MUTE-->999

=======================
3.How to Edit Patch key?
=======================
After Enable the Patch, go to Main Menu--->STB Setting-->Manual Key

======================
4.How to update the Patch key?
======================
1) Download the softcam.key from the internet.
2) Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
2) Connect your PC and receiver with twisted RS-232C cable.
3) Turn on the receiver and press "POWER" key to make it standby, the LED dot will blink.
4) Run the update tool on your PC,Slect the <Download Key>,press <Open> and select the softcam.key file,then click <Start>,upgrade will gin.
5) After finishing, the LED will display "-End"

============================
5.How to update Box to Box?
============================
a)Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
b)Connect the master receiver and the slave receiver with twisted RS-232C cable.
c)Turn on the master receiver and press "POWER" key to make it standby.
d)Turn on the slave receiver to begin update.
e)The LED of the master receiver will display "H" and blink it
f)Input the the password:(Only the first time)
111: To update S/W.
222: Channel Data
333: Channel Data first, then S/W
444: Copy Whole Flash except BootLoader
g)During the updating,the LED of the slave receiver will display "dxxx"(Receive the data to the SDRAM),"-ES-"(Erase the flash),then "Pxxx"(Put the date to the flash),at last it will display "-End"
h)Tune off the slave receiver,disconnect RS-232C cable and restart it
i)If you want to update another receiver,replace it with another receiver and turn on the receiver,it will start without inputting password.

=================================
6.How to upload the Channel Data?
=================================
a)Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
b)Connect your PC and receiver with twisted RS-232C cable.For safety,you should switch off the computer and the receiver before connection.
c)Turn on the receiver and press "POWER" key to make it standby
d)Run the upgrade tool on your PC, and config your correct COM.
e)Slect the <Upload Data>,then click <Start>,upload will begin.
f)During the uploading,the LED will display "Uxxx"(Upload the data to PC),at last it will display "-End".
g)After uploading,it will generate a file(*.SDX) on the same directry of the update tool[Upgrade],the path name will display on the File Status. This file includes all the satellites, transponders ,channels and settings.

======================
7. Hot Keys
======================
PGUP: All ECM List
PGDN: Current Key
INFO+2: RS232 Mode List

======================
8. Ethernet Sharing
======================
a) After factory default, Enable Patch. and make sure the RS45 small board embeded.
b) Searching channels.
c) Press INFO+2: and Select Ethernet CSC
d) Go to Main Menu-->Timer Setup-->IP Setting
In this menu, you can set the IP Address etc..., if the IP-Address is 0.0.0.0. It will get the IP automatically.
e) Go to Main Menu-->Timer Setup-->Server Setting.
In this menu, you can input the server by manul. After input the server, it will automally login the server and display
the server information at the bottom.

==============================
9.Loading G-Boy Game's Via USB
==============================
Download G-Boy Games from internet (G-Boy, extension (.gb, .gbc)
Play Game's Available Keys:
1) UP/DOWN/LEFT/RIGHT
2) 0/1/2
3) OK/EXIT
4) AUDIO

==============================
10. Change Start-up/Radio Logo
==============================
Note: It will replace the default logo.
10.1 -- Capture Pause Picture as Start-up/Radio Logo
1) Press "PAUSE" to pause the picture
a) Start-up Logo
b) Radio Logo
c) Cancel
Select a or b and wait some seconds for the converting.

10.2 -- Convert BMP/JPEG via USB as Start-up/Radio Logo
1) Play BMP/JPEG via USB
2) Press F1 key to save it as Start-up Logo or Radio Logo

==============================
11. LAN Home Shairing
==============================
This functions implemented for the Home Sharing, 1 CA receiver can connect with severial
Slave Lan Box based on G-Share protocol.

1) Insert the smartcard in the master LAN box, go to check the LAN box IP,
for example the IP is 192.168.0.5, this box is the g-share server with Port 2459.

2) Other LAN box can be slave, and go to Server Menu add the G-Share server as following
IP: Master LAN Box IP, for example 192.168.0.5
Port:2459 (Fixed)
Server Type:G-Share

The the slave can watch the channels which the Master CA supported.

You can also use it in the WAN, you need set the router Port, make the 2459 port(UDP) to the Master receiver IP,
And the slave box should set the WAN IP(the Router IP).

The internal default port 2459 can be changed in case in the LAN you can setup severial receivers as master.
go to IP Setting and press YELLOW key to chanage the port if needed.

==============================
11. Opb-P2P
==============================
11.1. Setting the Boudrate:
Main Menu--->STB Setting-->OSD Setting-->Opb Serial Baoudrate
115200,38400,9600

11.2. INFO+2 to call the RS232 Most List
And Select "Opb P2P Protocol"

11.3. It maybe be received the
"NOT_SUPPORTED!"
"NOT_ON_CARD!!!"
You need press INFO+F1:To Enable/Disable the log.

11.4. Note: You can call the "INFO+0" to call the All ECM List and select
correct CAID and ProvID to send to Master to decode.
Selected ID will be saved in the flash like the IP-BOX mode.
NOTE:
In "Opb P2P Protocol" mode, start-up will not detect the STB-->ST