Ремонт gi s8120

[credo]

Пробую разобраться со gi s8120, не грузится на табло boot , при переключении режимов загрузки err

Читать дальше... 

Board: STx7111-Mboard (MB618)  [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM:  128 MiB
NOR:     8 MiB
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
IdentID : 09 00 0b 00 01 49 cd
Hit ESC to stop autoboot:  0

Loading from NAND 512MiB 3,3V 8-bit, offset 0x18400000
   Image Name:   Linux-2.6.32.71_stm24_0217
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    2431464 Bytes =   2.3 MiB
   Load Address: 80801000
   Entry Point:  80802000
## Booting image at 80000000 ...
   Image Name:   Linux-2.6.32.71_stm24_0217
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    2431464 Bytes =   2.3 MiB
   Load Address: 80801000
   Entry Point:  80802000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90b0149cd

Starting kernel console=ttyAS0,115200 root=/dev/sda3 rw init=/bin/devinit coproc
essor_mem=4m@0x40000000,4m@0x40400000 printk=1 th0:off bigphysarea=6000 stmmacet
h=msglvl:0,phyaddr:1,watchdog:5000 rootdelay=9 nwhwconf=device:eth0,hwaddr:24:00
:0B:01:49:CD Manufacture=Spark-Project STB_ID=09:00:0B:00:01:49:CD - 0x00000000
- 0 ...

Linux version 2.6.32.71_stm24_0217 (@kubuntu) (gcc version 4.9.4 (GCC) ) #1 PREE
MPT Mon Nov 19 13:05:21 EET 2018
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS     - 00000000
... ORIG_ROOT_DEV     - 00000200
... LOADER_TYPE       - 00000000
... INITRD_START      - 00000000
... INITRD_SIZE       - 00000000
Booting machvec: sat7111
Node 0: start_pfn = 0x40000, low = 0x50000
Zone PFN ranges:
  Normal   0x00040000 -> 0x00050000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00040000 -> 0x00050000
Spark-7111 board initialization
STx7111 version 3.x
bpa2: partition 'bigphysarea' created at 0x49900000, size 25600 kB (0x01900000 B
)
bpa2: partition 'LMI_IO' created at 0x4b200000, size 79872 kB (0x04e00000 B)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyAS0,115200 root=/dev/sda3 rw init=/bin/devinit c
oprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 th0:off bigphysarea=6000 stm
maceth=msglvl:0,phyaddr:1,watchdog:5000 rootdelay=9 nwhwconf=device:eth0,hwaddr:
24:00:0B:01:49:CD Manufacture=Spark-Project STB_ID=09:00:0B:00:01:49:CD
bpa2: partition 'bigphysarea' created at 0x40e24000, size 24000 kB (0x01770000 B
)
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
PVR=04909200 CVR=60880000 PRR=00009a10
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 117888k/262144k available (3052k kernel code, 910k data, 124k init)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:600
Failed to enable clk CLKA_PLL0LS, ignoring
Console: colour dummy device 80x25
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 448.51 BogoMIPS (lpj=897024)
Mount-cache hash table entries: 512
CPU: STx7111
devtmpfs: initialized
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
sq: Registering store queue API.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 921, nTxLock = 7375
msgmni has been set to 230
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler cfq registered (default)
lirc_dev: IR Remote Control driver registered, major 61
lirc-stm: probe found data for platform device lirc-stm
lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
lirc_dev: lirc_register_driver: sample_rate: 0
STMicroelectronics LIRC driver initialized.
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
brd: module loaded
loop: module loaded
physmap platform flash device: 00800000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x000000000000-0x000000080000 : "Boot firmware"
0x000000080000-0x000000780000 : "Kernel"
0x000000780000-0x000000800000 : "Reserve"
NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bi
t)
stm-nand-emi: Using legacy platform timing data
stm-nand-emi: Configuring EMI Bank 1 for NAND access
cmdlinepart partition parsing not available
Creating 4 MTD partitions on "stm-nand-emi.0":
0x000000000000-0x000000800000 : "Spark Kernel"
0x000000800000-0x000018000000 : "Spark Rootfs"
0x000018000000-0x000018800000 : "kernel"
0x000018800000-0x00001ff00000 : "rootfs"
stmmac - user ID: 0x10, Synopsys ID: 0x33
 No HW DMA feature register supported
 Enhanced/Alternate descriptors
 RX Checksum Offload Engine supported
 TX Checksum insertion supported
 Wake-Up On Lan supported
STMMAC MII Bus: probed
eth0: PHY ID 00000000 at 0 IRQ 0 (0:00)
eth0: PHY ID 0007c0f1 at 1 IRQ 0 (0:01) active
eth0: PHY ID 00000000 at 2 IRQ 0 (0:02)
eth0: PHY ID 00000000 at 3 IRQ 0 (0:03)
eth0: PHY ID 00000000 at 4 IRQ 0 (0:04)
eth0: PHY ID 00000000 at 5 IRQ 0 (0:05)
eth0: PHY ID 00000000 at 6 IRQ 0 (0:06)
eth0: PHY ID 00000000 at 7 IRQ 0 (0:07)
eth0: PHY ID 00000000 at 8 IRQ 0 (0:08)
eth0: PHY ID 00000000 at 9 IRQ 0 (0:09)
eth0: PHY ID 00000000 at 10 IRQ 0 (0:0a)
eth0: PHY ID 00000000 at 11 IRQ 0 (0:0b)
eth0: PHY ID 00000000 at 12 IRQ 0 (0:0c)
eth0: PHY ID 00000000 at 13 IRQ 0 (0:0d)
eth0: PHY ID 00000000 at 14 IRQ 0 (0:0e)
eth0: PHY ID 00000000 at 15 IRQ 0 (0:0f)
eth0: PHY ID 00000000 at 16 IRQ 0 (0:10)
eth0: PHY ID 00000000 at 17 IRQ 0 (0:11)
eth0: PHY ID 00000000 at 18 IRQ 0 (0:12)
eth0: PHY ID 00000000 at 19 IRQ 0 (0:13)
eth0: PHY ID 00000000 at 20 IRQ 0 (0:14)
eth0: PHY ID 00000000 at 21 IRQ 0 (0:15)
eth0: PHY ID 00000000 at 22 IRQ 0 (0:16)
eth0: PHY ID 00000000 at 23 IRQ 0 (0:17)
eth0: PHY ID 00000000 at 24 IRQ 0 (0:18)
eth0: PHY ID 00000000 at 25 IRQ 0 (0:19)
eth0: PHY ID 00000000 at 26 IRQ 0 (0:1a)
eth0: PHY ID 00000000 at 27 IRQ 0 (0:1b)
eth0: PHY ID 00000000 at 28 IRQ 0 (0:1c)
eth0: PHY ID 00000000 at 29 IRQ 0 (0:1d)
eth0: PHY ID 00000000 at 30 IRQ 0 (0:1e)
eth0: PHY ID 00000000 at 31 IRQ 0 (0:1f)
nwhw_config: (eth0) setting mac address: 24:00:0b:01:49:cd
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xa0000000  size      0x00400000
                  cop. addr 0x40000000
    Channels : Not defined
    IRQ      : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xa0400000  size      0x00400000
                  cop. addr 0x40400000
    Channels : Not defined
    IRQ      : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac.0 handler (16 channels).
IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7111_0.elf
DMA: Registering fdma_dmac.1 handler (16 channels).
platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.3
IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7111_1.elf
platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.6
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
  #0: STMicroelectronics STx7111 cut 3.x SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Waiting 9sec before mounting root device...
Root-NFS: No NFS server available, giving up.
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "sda3" or unknown-block(2,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00             512 mtdblock0 (driver?)
1f01            7168 mtdblock1 (driver?)
1f02             512 mtdblock2 (driver?)
1f03            8192 mtdblock3 (driver?)
1f04          385024 mtdblock4 (driver?)
1f05            8192 mtdblock5 (driver?)
1f06          121856 mtdblock6 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

лог попытки восстановления usb

»»››ÛÛû·ÿ

Board: STx7111-Mboard (MB618)  [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM:  128 MiB
NOR:     8 MiB
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
IdentID : 09 00 0b 00 01 49 cd
Hit ESC to stop autoboot:  5
Force command mode:Select boot (current boot system : <NULL>):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
usage: fatload <interface> <dev[:part]> <addr> <filename> [bytes]
Using MAC Address FF:FF:FF:FF:FF:FF
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
STM-GMAC: PHY auto-negotiate timed out
STM-GMAC: *Warning* no link detected
*** ERROR: `serverip' not set

лог попытки восстановления лан

ïëûû

Board: STx7111-Mboard (MB618)  [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel

DRAM:  128 MiB
NOR:     8 MiB
NAND:  512 MiB
In:    serial
Out:   serial
Err:   serial
IdentID : 09 00 0b 00 01 49 cd
Hit ESC to stop autoboot:  5
Force command mode:Select boot (current boot system : <NULL>):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
usage: fatload <interface> <dev[:part]> <addr> <filename> [bytes]
Using MAC Address FF:FF:FF:FF:FF:FF
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
STM-GMAC: 100Mbs half duplex link detected
*** ERROR: `serverip' not set

Пожалуйста направьте советом по устранению неполадки?

[SGN]

Сообщение от credo

Пробую разобраться со gi s8120, не грузится на табло boot , при переключении режимов загрузки err

На материнке заменили кондер EL2 470мкф 10в?
------
з.ы. Имеются в наличии полностью рабочие 8120 и аналоги Amiko и GM, 11 штук, пульты только к пяти. Если кому-то нужны, пишите, договоримся. )))

[credo]

Я сегодня отправил в сервис на после гарантийное обслуживание.

[sattel77]

credo как Вам выше подсказали, можно было б заменить (для начала) все электролиты на материнке. Возраст то, у реса, почтительный

[SGN]

Сообщение от sattel77

можно было б заменить (для начала) все электролиты на материнке.

Чтобы рес запустился, достаточно было заменить всего один (что и сделают на сервисе), а остальные после.
Но хозяин - барин...

[sattel77]

Сообщение от SGN

достаточно было заменить всего один (что и сделают на сервисе), а остальные после.

Все верно;глядишь, через месяц-другой снова в ремонт

[SGN]

Сообщение от sattel77

через месяц-другой снова в ремонт

С идент-эррором. Не будет мастерская заморачиваться устранением всех потенциальных неисправностей.